Baby Nautiloid- 1lb Antweight Combat Robot

from $219.00
sold out

Baby Nautiloid Antweight Kit:
Baby Nautiloid is a feared competitive antweight winning many competitions all over the US since its creation in 2017.
Its nimble drivetrain and powerful disc make it easily the most fun robot to compete with I have ever designed.

The Base Kit requires adequate soldering skills and robot experience to complete. If you want to see what it takes to build your Base Kit into a Radio & Battery Ready Kit, check out the Build tab at the top of the page!

Due to the nature of combat robots I do not recommend this kit as a first robot. Despite their small size these can be incredibly dangerous and should always be handled with safety in mind. I recommend researching proper safety procedures for combat robots with active weapons.

Always test in an adequate test box.

Allow for up to 2 weeks for preparation and construction of your kit!

Baby Nautiloid Antweight Kit:
Baby Nautiloid is a feared competitive antweight winning many competitions all over the US since its creation in 2017.
Its nimble drivetrain and powerful disc make it easily the most fun robot to compete with I have ever designed.

The Base Kit requires adequate soldering skills and robot experience to complete. If you want to see what it takes to build your Base Kit into a Radio & Battery Ready Kit, check out the Build tab at the top of the page!

Due to the nature of combat robots I do not recommend this kit as a first robot. Despite their small size these can be incredibly dangerous and should always be handled with safety in mind. I recommend researching proper safety procedures for combat robots with active weapons.

Always test in an adequate test box.

Allow for up to 2 weeks for preparation and construction of your kit!

Completion Level:

  • Includes:

    Billet UHMW Chassis
    UHMW Inner Frames and Top Plates
    2x 1/4” AR500 Weapon Discs
    1/16” Grade 5 Ti Front Wedge
    CNC Machined 6061-T6 Weapon pulley with bearings
    1/4” Steel Weapon Shaft and hardware
    2x Weapon motor pullies
    2x Fingertech 55t Weapon Belt
    Hardware Kit containing all screws required
    3D Printed weapon lock

    Needed to complete:
    1x Pair of Fingertech’s 3mm Hubs
    1x Pair of 1.75”x 0.75” Fingertech Tires
    2x Repeat Drive Brushed Motors
    1x Scorpion Nano
    1x Emax RS2205 2600kv Weapon motor (I have tested motors as big as an EMAX 2306 however the RS2205 is still my favorite. Anything in this size with a 14mm by 16mm M3 hole pattern should fit and work well. I prefer standard right hand thread motors as this will keep your weapon motor pulley secure.)
    1x Flycolor Francy BLHeli_32 30A Weapon ESC with BEC
    1x iFlight FULLSEND 450mah 4s 75c Lipo, 1x Tattu 450mah 4s 75c Lipo (Long Size), or 1x MaxAmps 430mAh 4s Lipo with XT30 Connectors
    1x Fingertech Mini Power Switch
    1x Receiver (any small sized 4ch receiver should fit)
    1x Transmitter
    A few feet of 16ga wire
    Soldering Iron and solder
    XT30 connectors for battery connection
    MR30 connectors for motor connection
    JST Pigtails for drive motor connection

  • Includes everything in the Base Kit plus:

    1x Pair of Fingertech’s new Twist Snap Hubs
    1x Pair of 1.75”x 0.75” Fingertech Tires
    2x Repeat Drive Brushed Motors
    1x Scorpion Nano
    1x Emax RS2205 2600kv Weapon motor
    1x 30-45amp Weapon Esc (exact model may vary as different ESCs go in and out of stock)
    1x Fingertech Mini Power Switch
    1x Wiring Harness

    Needed to complete:

    1x Receiver
    1x Transmitter
    1x iFlight FULLSEND 450mah 4s 75c Lipo, 1x Tattu 450mah 4s 75c Lipo (Long Size), or 1x MaxAmps 430mAh 4s Lipo with XT30 Connectors